Mon-Fri 9am-5pm local timeA referral service: we connect you with independent repair companies near you
Appliance Guidebook
(888) 280-5160
  1. Home
  2. Electrolux
  3. Dryer
  4. E64

Electrolux dryer code E64: what it means and how to fix it

An Electrolux dryer with E64 may stop mid-cycle, beep, quit heating, or still make some heat before it fails again. This guide explains what the code points to, what you can check safely, and what a technician will test inside the dryer.

Call to be connected(888) 280-5160

A person answers Mon-Fri 9am-5pm local time. Outside those hours, leave a message and a company near you calls back.

Answered by an independent appliance repair company that serves your area. Not a call center.

What the display shows
Straight answer

Electrolux dryer code E64 means the control sees an open heating element circuit. The first checks are the heater coils and heater wiring; restricted airflow can overheat the heater area, but the code itself points to an open circuit.

Check these first

Safe to do yourself. Unplug the appliance before you start.

  1. Reset the control

    Turn the dryer off, unplug it, wait 1 to 2 minutes, then plug it back in. If E64 comes right back, the control is seeing a real heat-circuit fault, so don't keep restarting it over and over.

  2. Clean the lint screen fully

    Pull the lint screen and remove the lint by hand. If fabric softener film is on the mesh, wash it with mild soap and a soft brush, rinse it, then let it dry before reinstalling it.

  3. Check the outside vent flow

    If the dryer will run on Air Dry or No Heat, run it briefly and feel for strong airflow at the outside vent. Weak flow, a flap that barely opens, or lint packed at the hood can overheat the heater area, so stop if the code returns or you notice burning smells.

  4. Look at the vent hose

    Unplug the dryer before moving it. Flexible foil or plastic venting isn't approved and can crush or hold lint; use the vent material called for in the installation guide and correct airflow before replacing parts.

  5. Try a no-heat cycle once

    If E64 appears even on Air Dry, that doesn't rule out the heater circuit. On some multi-coil heaters, one section can be open while another still heats, and wiring or heater sensing still needs testing.

Side view of a dryer venting through a transition hose and wall duct to an outside flapLint screenTransition hose: crush pointWallOutside flap
Air leaves through the lint screen, the transition hose and the wall duct to the outside flap. A crushed hose or packed duct causes most heat and long-dry problems.
When it's a repair

A technician usually starts with the heating element and its harness because E64 is a heater-open fault on the tech sheet. Next are loose or burned heater connectors, open wiring between the control and heater, and power feed or terminal block damage when there are heat marks. The electronic control comes after the heater and wiring test good. Thermal limiters, high-limit thermostats, and thermistors are checked when the model's tech sheet, a no-heat symptom, or another stored code points there. If the dryer is around 15 years old, has drum support noise, cabinet rust, or prior control issues, repair value gets harder to justify.

Models where this shows up most

This fault path also applies to many Frigidaire dryers because Frigidaire is under Electrolux and many designs share heat-system parts. A common field detail is the multi-coil heater assembly: one sagged coil can make the dryer act odd before it goes fully open.

Have the model number ready

The company will ask for it first. It's on a sticker or metal plate, usually in one of these spots:

Where the model tag usually is on a dryer12
  1. Inside the door opening, on the frame
  2. Some models: on the back panel
Worth knowing

Conditions that make this more likely

Lint and dust build up faster than you'd think

Dryer vents, refrigerator condenser coils and dishwasher filters collect lint, pet hair and dust. Homes with pets, long vent runs or dusty surroundings usually need these cleaned more than once a year.

Check both breakers

Electric dryers and ranges run on a double 240V breaker. If only one leg trips, the drum can spin or the display can light with no heat. Reset both halves before assuming the appliance has failed.

What a technician tests

Most likely part first. These are for a technician with a meter and the tech sheet, not a weekend project.

PartHow it's tested
Heating elementUnplug the dryer, isolate the heater leads, and read the element across its terminals. A good element should match the model's tech sheet; an open reading points to a broken coil. Visible gaps, sagged coils, charring, or melted spots also fail it.
Heating element to groundCheck each heater terminal to the metal heater housing. Any continuity to the housing means the element is grounded and must be replaced. That is usually a heater-to-ground fault, so use the stored code and the model tech sheet together.
Thermal limiter or fuseWith the dryer unplugged, pull one wire from the limiter or fuse and test continuity through it. No continuity means it has opened, often after restricted airflow or an overheated heater area.
High-limit thermostat or thermistorFor high-limit or limiter devices, test for continuity with the wires removed; they should be closed at room temperature. Thermistors are not simple continuity switches, so compare their resistance with the model tech sheet before replacing them.
Heater wiring and terminal blockInspect the heater connectors, cord terminals, and nearby wiring for loose spades, darkened plastic, or overheated metal. If the element tests good, the technician checks for proper line voltage feeding the heat circuit before condemning the control.

Don't see your symptom?

Describe it on the phone. The company on the other end works on these every day and will know what to ask.

Call to be connected(888) 280-5160

Other Electrolux dryer problems

E63Electrolux dryer E63 code: what it means and how to fix it

On many Electrolux/Frigidaire-built full-size electric dryers, E63 means heater to earth ground or heater short, not…

Read the fix →

Electrolux dryer not drying: what to check first

An Electrolux dryer not drying means the machine isn’t moving enough warm air through the load, isn’t heating correctly,…

Read the fix →

Electrolux dryer not starting: what it means and how to fix it

An Electrolux dryer not starting means the dryer is missing one of the run conditions: closed door signal, good power,…

Read the fix →

Common questions about appliance repair

Can I clear Electrolux dryer code E64 with a reset?

A reset can clear a control glitch. If the code returns during the next cycle, expect a heater-circuit fault that needs testing.

Why does my dryer still heat with E64?

A heating element can fail in one section, sag, or open only part of a multi-coil assembly. That can leave some heat while the control still detects an open heater circuit.

Will cleaning the vent fix E64?

Cleaning the vent can help if poor airflow caused an overheat. If the element is already burned open or grounded, the part still has to be replaced.

Is E64 the same on Frigidaire and Electrolux dryers?

Often, yes. Many Frigidaire dryers use Electrolux-style designs, so E64 points to the same heat-system checks.

Can I keep using the dryer with E64?

It's safer to stop using it until the lint path is clear and the heater circuit is checked. A grounded or overheated element can damage nearby parts.

Still showing the problem after the checks?

Call and describe what you tried. You'll be connected with an independent repair company near you.

(888) 280-5160