Maytag oven error codes: what each one means

Use this table to match the display code with what the control detected and the first safe check to try. Maytag uses several oven and range control platforms, so confirm with the model manual or tech sheet when a code description differs by model.

Call to be connected(888) 280-5160

A person answers Mon-Fri 9am-5pm local time. Outside those hours, leave a message and a company near you calls back.

Answered by an independent appliance repair company that serves your area. Not a call center.

Reading the code

Codes usually appear on the oven or range control display as F, F# E#, or E# F# formats. To clear one, unplug the range or turn the breaker off for 1 minute, restore power, and monitor the display for about 1 minute. LOC, Lock or Locked means Control Lock, SAB, Sab, 5AB or 5A6 means Sabbath mode, CAL is calibration, C is Celsius display, PF is power failure, Demo Mode is a setting, and these are status messages rather than part faults.

Have the model number ready

The company will ask for it first. It's on a sticker or metal plate, usually in one of these spots:

Behind the storage drawer, on the frame
Or on the oven frame, visible with the door open

Maytag oven & range error codes

Covers Maytag ranges, wall ovens and combination wall ovens; older models may show F codes, while many newer controls show F# E# or E# F# formats.

20 codes

CodeWhat it meansCheck firstUsually

F9 / F9 E0The control detected a miswired electrical supply, an outlet or hard wire connection problem, or incorrect voltage noise.Turn the breaker off for 1 minute and restore power; if it returns, a qualified electrician or a technician should check the supply wiring.Usually a technician

F1The control detected a problem with the oven temperature sensor, control, or related wiring.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F0 E0The electronic oven control cannot identify the exact control system fault.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F1 E0The control detected a touchpad, user interface, EEPROM communication, or main control fault.Turn power off for 1 minute, restore it, and call a technician if the display repeats the code.Usually a technician

F2 E0 to F2 E6The control detected a user interface or keypad circuit problem, such as a disconnected keypad, stuck key, or cancel key error.Turn power off for 1 minute, then make sure no key is stuck, wet, or being pressed before restoring power.Often a home check

F3 E0 to F3 E3The control detected an oven temperature sensor, control, or sensor wiring problem; upper, lower, main, and warming drawer sensors vary by model.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F5 E0 to F5 E7The control detected that the door latch, door switch, or related wiring does not match the expected door position.Make sure the door is fully closed and not being forced, then reset power for 1 minute.Usually a technician

F6 E1 / F6 E2 / F6 E3On some range controls, the control detected an over temperature condition during cooking, cleaning, or warming drawer operation.If the oven is hot or heating on its own, turn it off at the breaker and let it cool before calling a technician.Usually a technician

F6 E0 / F6 E1 / F6 E2The control detected a fault that can involve the appliance manager, converter control, user interface, or wiring, depending on the exact code and model.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F8 E0 / F8 E1 / F8 E3The control detected a cooling fan or airflow problem; on double ovens the code may identify the upper or lower fan.Check that nothing is blocking exterior oven vents, then reset power for 1 minute.Usually a technician

F8 E2The control detected cooling fan speed outside the expected range, often a fan speed or fan sensor issue.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F8 E4 / F8 E5The control detected a problem with the exhaust fan air temperature sensor or its wiring.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F8 EAThe control detected a user interface or related wiring problem.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F8The control is not reading the meat probe correctly or the probe connection is not secure.Make sure the meat probe is fully seated in the probe jack, then reset power if the display stays on.Often a home check

F7 E0On steam wall oven models, the control detected a water level, water level sensor, or related wiring problem.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F7 E6The control detected a cooling fan or fan wiring problem on some range models.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F1 E7 / F1 E9The control detected an appliance control board problem or related wiring fault.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F1 E5On some models this points to a sensor out of range, while combination wall ovens may use it for a microwave inverter, magnetron, or wiring fault.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F1 E7The control detected a PCB thermistor or control temperature sensing fault on some range controls.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

F1 E9The control detected an internal control queue or control logic fault on some range controls.Turn power off for 1 minute, restore it, and call a technician if the code returns.Usually a technician

Don't see your symptom?

Describe it on the phone. The company on the other end works on these every day and will know what to ask.

Call to be connected(888) 280-5160

Other Maytag oven & range problems

Maytag oven not heating: what to check first

A Maytag oven not heating means the bake system is not being powered, not igniting gas, or not getting a usable…

Read the fix →

Common questions about appliance repair

How do I reset a Maytag oven error code?

Unplug the range or turn the oven breaker off for 1 minute, restore power, then watch the display for about 1 minute. If the code comes back, a technician should diagnose it.

Why does F9 E0 keep coming back?

F9 E0 usually means the control still sees a power supply or wiring problem. A qualified electrician or a technician should verify the outlet, hard wire connection and supply voltage.

Are LOC, SAB, PF and C error codes?

They are usually status or setting messages, not part failures. LOC means Control Lock, SAB means Sabbath mode, PF means a power failure, and C means the display is set to Celsius.

Why do older Maytag oven codes differ from newer F# E# codes?

Maytag uses several control platforms. Older models may show short F codes, while many newer controls show F# E# or E# F# formats.

Still showing the problem after the checks?

Call and describe what you tried. You'll be connected with an independent repair company near you.

(888) 280-5160