Mon-Fri 9am-5pm local timeA referral service: we connect you with independent repair companies near you
Appliance Guidebook
(888) 280-5160
  1. Home
  2. Samsung
  3. Dryer
  4. BE

Samsung dryer code bE: what it means and how to fix it

Your Samsung dryer may beep, stop before a cycle starts, or show bE, bE2, bC2, 6E, 6E2, or 6C2 on the display. This page explains what the code means, what you can safely try at the console, and when the user interface needs a technician.

Call to be connected(888) 280-5160

A person answers Mon-Fri 9am-5pm local time. Outside those hours, leave a message and a company near you calls back.

Answered by an independent appliance repair company that serves your area. Not a call center.

Straight answer

The Samsung dryer code bE means the control thinks one of the console buttons is stuck or being held down. The single most common cause is a jammed, sticky, or worn button on the control panel.

Check these first

Safe to do yourself. Unplug the appliance before you start.

  1. Power the dryer off

    Turn the dryer off at the control. If it’s easy to reach the plug, unplug it for about one minute, then power it back up and check the display.

  2. Press every button edge to edge

    With the dryer off, press and release each button one at a time. Work around the edges of each key, because a Samsung button can hang up slightly on one side while it still looks normal from the front.

  3. Feel for one bad button

    A problem button may feel mushy, stay low, click oddly, or fail to spring back. Don’t force it. Repeated hard pressing can make a weak keypad worse.

  4. Clean the control area lightly

    Wipe around the buttons with a soft cloth that is only lightly damp, then dry the panel fully. Detergent film, lint, or moisture near the keypad can make a button read as pressed.

  5. Try one short cycle

    After the panel is dry, start a timed dry cycle. If the bE code returns right away, the dryer is probably reading a stuck key inside the console rather than seeing a one-time glitch.

When it's a repair

A technician usually starts with the console buttons and user interface keypad, then moves to the display board or main control PCB if the keypad is sending a false button signal. If the panel is cracked, a button is physically collapsed, or the code comes back as soon as power is restored, the console assembly is often the part being replaced. This repair can make sense on a newer or midlife dryer with a clean cabinet. If the dryer is older, has other heat or drum wear issues, or the matching control parts are no longer stocked, I’d lean away from putting much repair time into it.

Worth knowing

Conditions that make this more likely

Boards fail earlier in hot rooms

Electronics are rated for room temperature. In a garage or an unconditioned laundry room in summer, a control board can sit well above that for hours a day. Before replacing a board, a good technician confirms the parts it controls test good, since a shorted pump or valve can take out a new board too.

Lint and dust build up faster than you'd think

Dryer vents, refrigerator condenser coils and dishwasher filters collect lint, pet hair and dust. Homes with pets, long vent runs or dusty surroundings usually need these cleaned more than once a year.

What a technician tests

Most likely part first. These are for a technician with a meter and the tech sheet, not a weekend project.

PartHow it's tested
Console buttonsWith power removed, the tech checks each key for a normal click and full return. A key that sits low, binds at the edge, or feels gummy is treated as the likely cause before any board is condemned.
User interface keypadThe tech uses the model’s service sheet or diagnostic mode to see whether a key input is stuck with no one touching the panel. On some Samsung dryers, holding Dryness and Wrinkle Prevent for 6 seconds brings up stored error information, which helps confirm the button fault family.
User interface boardThe console is opened by a technician and inspected for moisture tracks, residue, cracked button pads, or damaged traces at the keypad board. If the stuck input follows the UI board with all buttons released, the UI is the suspect.
UI-to-main control wire plugThe tech checks the plug between the console and the main PCB for loose fit, corrosion, or pin damage. A poor connection can make the main board read bad key data, though it’s less common than a stuck key or failed UI.
Main control PCBIf the keypad and UI checks pass, the main PCB is checked for a false input fault after reset and during diagnostic testing. A board that keeps logging the same button error with a known good console becomes the final suspect.

Don't see your symptom?

Describe it on the phone. The company on the other end works on these every day and will know what to ask.

Call to be connected(888) 280-5160

Other Samsung dryer problems

CL9Samsung dryer CL9 code: what it means and what to check

A Samsung dryer CL9 code shows up after the Vent Blockage test and means the dryer thinks airflow is badly restricted,…

Read the fix →

DCSamsung dryer code dc: what it means and how to fix it

The samsung dryer code dc means the dryer control doesn't see the door as shut, so it stops or won't start the cycle.…

Read the fix →

DESamsung dryer DE code: what it means and what to check

The Samsung dryer DE code means the dryer is reading the door as open, unlatched, or not proven closed by the door…

Read the fix →

HCSamsung dryer HC code: what it means and what to check

The samsung dryer hc code means the dryer has detected a heating fault, usually an overheat condition, and it stops the…

Read the fix →

HESamsung dryer HE code: what it means and what to check

The Samsung dryer HE code means the dryer thinks it is overheating. The single most common cause is trapped heat from a…

Read the fix →

Samsung dryer not drying: what it means and what to check first

A Samsung dryer not drying means it has lost heat, lost airflow, or is ending the cycle before the clothes are actually…

Read the fix →

Common questions about appliance repair

Can I reset a Samsung dryer code bE?

Yes. Turn the dryer off, unplug it for about one minute if you can reach the plug, then restore power. If the code returns, reset alone won’t fix a stuck key or failed console.

Are bE, bE2, bC2, and 6E the same problem?

They’re in the same stuck-button fault group on Samsung dryers. The exact letters vary by model, but the first check is still the control panel buttons.

What if no button feels stuck?

The keypad can fail electrically even when every button feels normal. At that point a technician checks the user interface board, the wire plug to the main board, and then the main PCB.

Is this a vent or heating problem?

Usually no. Vent clogs are tied to Samsung temperature and heating codes, while bE points to the console button circuit.

Should I keep using the dryer with a bE code?

No. If the control thinks a button is held down, it may cancel cycles or ignore commands. Clear the stuck button first, then call a repair company if the code comes back.

Still showing the problem after the checks?

Call and describe what you tried. You'll be connected with an independent repair company near you.

(888) 280-5160