Frigidaire F10 oven code: what it means and how to fix it
Your Frigidaire range is beeping, flashing F10, or shutting down during bake or broil. Sometimes the oven really is too hot. Other times the small rear temperature probe is lying to the control, and this page shows what to check safely before a technician tests parts.
A person answers Mon-Fri 9am-5pm local time. Outside those hours, leave a message and a company near you calls back.
Answered by an independent appliance repair company that serves your area. Not a call center.
The Frigidaire F10 oven code means the control sees a thermal runaway condition, so it thinks the oven is overheating or heating when it should be off. The oven temperature sensor, also called the RTD probe, is the first part a technician usually checks, but wiring or the electronic oven control can also cause it.
Check these first
Safe to do yourself. Unplug the appliance before you start.
- Stop the cycle and cut power if it keeps heating
Press Cancel or Clear once. If the beeping continues, the oven keeps heating, or the control won't respond, turn the range breaker off and leave the oven alone until it cools.
- Do a power reset
After the oven is cool, disconnect power at the plug or breaker for at least 30 seconds. Five minutes is also fine if the range was very hot. If this was a one-time control glitch, the code may clear here.
- Remove foil from the oven floor
When the oven is cool, look for foil on the oven bottom. Foil and liners can block air flow, trap heat, damage the oven floor, and throw off normal baking.
- Check the rear sensor area without taking panels off
The sensor is the thin pencil-shaped metal probe on the back wall of the oven cavity, often near the upper rear corner. Make sure a large pan, rack, or baked-on food is not touching it.
- Try one short bake test
Restore power only if the oven is cool and didn't start heating by itself. Run Bake at 350°F while you stay nearby. If F10 returns during preheat, press Cancel or Clear. If heat continues or the controls don't respond, turn the breaker off and stop testing.
Every Frigidaire oven & range error code in one table, with what each means and what to check first →
The company will ask for it first. It's on a sticker or metal plate, usually in one of these spots:
- Behind the storage drawer, on the frame
- Or on the oven frame, visible with the door open
Conditions that make this more likely
Boards fail earlier in hot rooms
Electronics are rated for room temperature. In a garage or an unconditioned laundry room in summer, a control board can sit well above that for hours a day. Before replacing a board, a good technician confirms the parts it controls test good, since a shorted pump or valve can take out a new board too.
What a technician tests
Most likely part first. These are for a technician with a meter and the tech sheet, not a weekend project.
Don't see your symptom?
Describe it on the phone. The company on the other end works on these every day and will know what to ask.
Other Frigidaire oven & range problems
F1F1 code on a Frigidaire oven: what it means and what to check
On many Frigidaire electric ranges, F1 means the control has detected a shorted keypad. On some older Frigidaire…
Read the fix →F11F11 code Frigidaire range: what it means and what to check
The F11 code Frigidaire range fault means the oven control sees a key as held down or shorted; on some models, the tech…
Read the fix →F31Frigidaire oven code F31: what it means and what to check
Frigidaire oven code F31 means the control sees a shorted oven temperature probe circuit. Common causes are a shorted…
Read the fix →F90F90 code Frigidaire oven: what it means and what to check
The F90 code on a Frigidaire oven means the electronic oven control is detecting a door lock problem, often because it…
Read the fix →Frigidaire oven not heating: what it means and what to check
A Frigidaire oven not heating means the bake system is not getting usable heat from the element, igniter, power supply,…
Read the fix →Frigidaire oven gas not working: what to check first
A Frigidaire oven gas not working usually means the bake burner is not lighting or the control is not sending the right…
Read the fix →Common questions about appliance repair
Can I keep using the oven after an F10 code?
No, stop using it if F10 comes back. Thermal runaway can mean the oven is overheating or that a relay is feeding an element when it shouldn't.
Will resetting the breaker fix a Frigidaire F10 oven code?
A reset can clear a brief control glitch or power surge. If the code returns during one short 350°F bake test, assume there is a part or wiring fault.
Is F10 usually the sensor or the control board?
The temperature sensor is the usual first suspect because it tells the board how hot the oven is. The control board becomes likely when the sensor and wiring test properly, or when an element stays powered with the oven canceled.
Can self-clean trigger F10?
High heat can expose a weak sensor connection or a failing control. Let the oven cool fully before testing once, and stop if F10 returns.
What if the range was installed recently?
If it was installed within the first 30 days, contact the installer or the manufacturer before opening anything. A wiring, setup, or early part issue may need to be documented.
Still showing the problem after the checks?
Call and describe what you tried. You'll be connected with an independent repair company near you.